Troubleshooting
Power
My Shark Glam won't turn on or switches off on its own. What should I do?
1. Plug the styler into a power point you know works. 2. Slide the power button up to turn it on. 3. If your plug has Test and Reset buttons, press Test, then Reset, before every use, then slide the power button up. If any of the temperature or airflow lights are blinking, note which lights and what colour, then see the matching error light question on this page. If it switches off while you're using it, unplug any other appliances being used in the same room and try again. This is a high-powered styler and should only be used with a power point that supplies the right voltage. It shouldn't be used with a voltage converter, a power board or an extension lead. If it still won't turn on or keeps switching off, please contact us. It helps to have a photo of the label showing the model and serial number, your proof of purchase, and a photo or short video of the fault ready.
Airflow
Why is the airflow on my Shark Glam weaker than usual?
First, press the airflow button (the one with the fan on it) to step the airflow up to the setting you want. Next, make sure your hand isn't covering the filter cover at the bottom of the unit while you use it, as this blocks the air inlet and reduces airflow. If the airflow is still reduced, dust build-up on the filter is the usual cause, so clean it: 1. Switch the styler off and unplug it. 2. Slide the filter cover off the bottom of the unit. 3. Gently brush away any built-up dust from the filter screen using a new toothbrush, or wipe it with a dry microfibre cloth. 4. Slide the filter cover back onto the bottom of the unit until it clicks into place, then switch the styler back on. Cleaning the filter once a month helps keep your Shark Glam performing well and helps prevent overheating. If any of the temperature or airflow lights are blinking, note which lights and what colour, then see the matching error light question on this page. If the airflow is still reduced after cleaning, please contact us. It helps to have a photo of the label showing the model and serial number, your proof of purchase, and a photo or short video of the fault ready.
Heat
My Shark Glam is overheating or switching itself off. What can I do?
Your Shark Glam has a built-in thermostat that switches it off if it overheats. This can happen if it's been running for a long time, or if there's a blockage or dust build-up. 1. Remove any accessories that are attached. 2. Check the lights. If any of the temperature or airflow lights are blinking, note which lights and what colour, then see the matching error light question on this page. 3. If no lights are blinking, press the Cool Shot button to cool the styler down. It blows room-temperature air and helps it cool faster. 4. Once it's cooled, clean the filter: 1. Switch the styler off and unplug it. 2. Slide the filter cover off the bottom of the unit. 3. Gently brush away any built-up dust from the filter screen using a new toothbrush, or wipe it with a dry microfibre cloth. 4. Slide the filter cover back onto the bottom of the unit until it clicks into place, then switch the styler back on. Cleaning the filter once a month helps keep your Shark Glam performing well and helps prevent overheating. Make sure your hand isn't covering the filter cover while you use it, as this can also cause overheating. The styler will feel warm to the touch during and straight after use, as warm air flows through it. A lower heat setting or the Cool Shot button can help keep it cooler while you style. If you look into the nozzle and the heater coils are glowing red, or it keeps overheating after cleaning, please contact us. It helps to have a photo of the label showing the model and serial number, your proof of purchase, and a photo or short video of the fault ready.
Why does my Shark Glam have a burning smell?
Start by looking closely at the nozzle. If it looks warped, melted or out of shape, please stop using the styler and contact us. If the nozzle looks normal, switch the styler off, unplug it and set it aside to cool. Then clean the filter, as dust build-up is the usual cause: 1. Switch the styler off and unplug it. 2. Slide the filter cover off the bottom of the unit. 3. Gently brush away any built-up dust from the filter screen using a new toothbrush, or wipe it with a dry microfibre cloth. 4. Slide the filter cover back onto the bottom of the unit until it clicks into place, then switch the styler back on. Cleaning the filter once a month helps keep your Shark Glam performing well and helps prevent overheating. If it still smells like something is burning after cleaning, stop using it and please contact us. It helps to have a photo of the label showing the model and serial number, your proof of purchase, and a photo or short video of the fault ready.
My Shark Glam has some discolouration. Is it still safe to use?
Yes, the styler is still safe to use. Some discolouration can develop when it's used on high heat for long periods. To help avoid more, press the Cool Shot button to cool it down when you've been using a high temperature for a while. It's also worth cleaning the filter once a month: 1. Switch the styler off and unplug it. 2. Slide the filter cover off the bottom of the unit. 3. Gently brush away any built-up dust from the filter screen using a new toothbrush, or wipe it with a dry microfibre cloth. 4. Slide the filter cover back onto the bottom of the unit until it clicks into place, then switch the styler back on.
Why is my Shark Glam smoking?
If you're using a styling product in your hair, it can create smoke when it meets a hot tool. For example, coconut oil has a smoke point of around 176 to 204°C. Always read and follow the safety warnings and instructions on your hair styling products before use. If you're using a heat protectant, wait a few minutes for it to set before you start styling. If you're not using any product in your hair and the styler is smoking, stop using it and please contact us. It helps to have a photo of the label showing the model and serial number, your proof of purchase, and a photo or short video of the fault ready.
Why are my Shark Glam accessories hot to touch?
It's normal for the accessories to feel warm during use. For your comfort, always hold them by the cool-touch areas. Tip: hold down the Cool Shot button to cool the accessory before you remove it. To remove an accessory, slide the top lock down, then lift and twist the accessory to the right while holding the cool-touch points.
Error lights
What does it mean when all three airflow lights are blinking white?
This points to dust build-up, which can cause overheating and strain the motor. Clean the filter: 1. Switch the styler off and unplug it. 2. Slide the filter cover off the bottom of the unit. 3. Gently brush away any built-up dust from the filter screen using a new toothbrush, or wipe it with a dry microfibre cloth. 4. Slide the filter cover back onto the bottom of the unit until it clicks into place, then switch the styler back on. If the lights are still blinking, set the styler aside to cool in a room-temperature space for about 30 minutes, then switch it on again. If they're still blinking after that, please contact us. It helps to have a photo of the label showing the model and serial number, your proof of purchase, and a photo or short video of the fault ready.
What does it mean when the left airflow light is blinking white?
This means the power point isn't supplying the right voltage and the styler is detecting under-voltage. This is a high-powered styler and should only be used with a power point that supplies the right voltage. It shouldn't be used with a voltage converter, a power board or an extension lead. Try plugging the styler into a different power point in another room. If the light is still blinking, please contact us. It helps to have a photo of the label showing the model and serial number, your proof of purchase, and a photo or short video of the fault ready.
What does it mean when the middle airflow light is blinking white?
This means the power point isn't supplying the right voltage and the styler is detecting over-voltage. This is a high-powered styler and should only be used with a power point that supplies the right voltage. It shouldn't be used with a voltage converter, a power board or an extension lead. Try plugging the styler into a different power point in another room. If the light is still blinking, please contact us. It helps to have a photo of the label showing the model and serial number, your proof of purchase, and a photo or short video of the fault ready.
What does it mean when the right airflow light is blinking white?
This means the power point isn't supplying the right electrical current and the styler is detecting over-current. This is a high-powered styler and should only be used with a power point that supplies the right voltage. It shouldn't be used with a voltage converter, a power board or an extension lead. Try plugging the styler into a different power point in another room. If the light is still blinking, please contact us. It helps to have a photo of the label showing the model and serial number, your proof of purchase, and a photo or short video of the fault ready.
What does it mean when the left and middle airflow lights are blinking white?
This means the styler is overheating. 1. Switch it off and on again. 2. If the lights are still blinking, clean the filter: 1. Switch the styler off and unplug it. 2. Slide the filter cover off the bottom of the unit. 3. Gently brush away any built-up dust from the filter screen using a new toothbrush, or wipe it with a dry microfibre cloth. 4. Slide the filter cover back onto the bottom of the unit until it clicks into place, then switch the styler back on. 3. If they're still blinking, set the styler aside to cool in a room-temperature space for about 30 minutes, then switch it on again. If they're still blinking after that, please contact us. It helps to have a photo of the label showing the model and serial number, your proof of purchase, and a photo or short video of the fault ready.
What does it mean when the left and right airflow lights are blinking white?
This means there could be an issue with the connection between the accessory and the styler. 1. Switch the styler off. 2. If your plug has a Reset button, press it, then switch the styler on again. 3. If the lights are still blinking, remove the accessory and turn it upside down. You'll see several shiny gold pins on the bottom. Wipe the pins with a dry microfibre cloth to remove any liquid or debris. 4. Reattach the accessory, making sure it's fully locked in: line up the open arrow on the accessory with the arrow on the back of the styler, then press and twist until the solid arrow lines up and it clicks into place. 5. Switch the styler on again. Avoid resting accessories on wet surfaces, as moisture on the pins can cause this error. If the lights are still blinking, please contact us. It helps to have a photo of the label showing the model and serial number, your proof of purchase, and a photo or short video of the fault ready.
What does it mean when all three temperature lights are blinking red?
This means the styler is overheating. 1. Switch it off and on again. 2. If the lights are still blinking, clean the filter: 1. Switch the styler off and unplug it. 2. Slide the filter cover off the bottom of the unit. 3. Gently brush away any built-up dust from the filter screen using a new toothbrush, or wipe it with a dry microfibre cloth. 4. Slide the filter cover back onto the bottom of the unit until it clicks into place, then switch the styler back on. 3. If they're still blinking, set the styler aside to cool in a room-temperature space for about 30 minutes, then switch it on again. If they're still blinking after that, please contact us. It helps to have a photo of the label showing the model and serial number, your proof of purchase, and a photo or short video of the fault ready.
What does it mean when the left temperature light is blinking red?
This means the styler is overheating. Press the Cool Shot button to cool it down. It blows room-temperature air and helps it cool faster. Once it's cooled, clean the filter: 1. Switch the styler off and unplug it. 2. Slide the filter cover off the bottom of the unit. 3. Gently brush away any built-up dust from the filter screen using a new toothbrush, or wipe it with a dry microfibre cloth. 4. Slide the filter cover back onto the bottom of the unit until it clicks into place, then switch the styler back on. Cleaning the filter once a month helps keep your Shark Glam performing well and helps prevent overheating. If the light is still blinking after cleaning, please contact us. It helps to have a photo of the label showing the model and serial number, your proof of purchase, and a photo or short video of the fault ready.
What does it mean when the middle temperature light is blinking red?
This means the styler isn't reaching the set temperature. 1. Switch it off, leave it off for a minute, then switch it on again. 2. If the light is still blinking, plug the styler into a different power point in another room. This is a high-powered styler and should only be used with a power point that supplies the right voltage. It shouldn't be used with a voltage converter, a power board or an extension lead. If the light is still blinking, please contact us. It helps to have a photo of the label showing the model and serial number, your proof of purchase, and a photo or short video of the fault ready.
What does it mean when the right temperature light is blinking red?
This means the styler has detected a blockage in the motor. 1. Switch it off, unplug it, then plug it back in and switch it on again. 2. If the light is still blinking, slide off the filter cover and check the filter for any damage, such as cracks or holes. 3. Gently shake the styler and listen for anything rattling around inside. If the light is still blinking, the filter is damaged, or you hear a rattle, please contact us. It helps to have a photo of the label showing the model and serial number, your proof of purchase, and a photo or short video of the fault ready.
What does it mean when the left and right temperature lights are blinking red?
This means there could be an issue with the connection between the accessory and the styler. 1. Switch the styler off. 2. If your plug has a Reset button, press it, then switch the styler on again. 3. If the lights are still blinking, remove the accessory and turn it upside down. You'll see several shiny gold pins on the bottom. Wipe the pins with a dry microfibre cloth to remove any liquid or debris. 4. Reattach the accessory, making sure it's fully locked in: line up the open arrow on the accessory with the arrow on the back of the styler, then press and twist until the solid arrow lines up and it clicks into place. 5. Switch the styler on again. Avoid resting accessories on wet surfaces, as moisture on the pins can cause this error. If the lights are still blinking, please contact us. It helps to have a photo of the label showing the model and serial number, your proof of purchase, and a photo or short video of the fault ready.
What does it mean when the right and middle temperature lights are blinking red?
This means the styler isn't reaching the set temperature. Switch it off, leave it off for a minute, then switch it on again. If the lights are still blinking, try this once more. If they're still blinking after that, please contact us. It helps to have a photo of the label showing the model and serial number, your proof of purchase, and a photo or short video of the fault ready.
What does it mean when the left and middle temperature lights are blinking red?
This means the styler has been in a hot environment for too long. Switch it off, unplug it and leave it to cool in a room-temperature space for about 30 minutes, then switch it on again. If the lights are still blinking, please contact us. It helps to have a photo of the label showing the model and serial number, your proof of purchase, and a photo or short video of the fault ready.
What does it mean when the left airflow light is blinking white and all three temperature lights are blinking red?
This means there could be an issue with the connection between the accessory and the styler. 1. Switch the styler off. 2. If your plug has a Reset button, press it, then switch the styler on again. 3. If the lights are still blinking, remove the accessory and turn it upside down. You'll see several shiny gold pins on the bottom. Wipe the pins with a dry microfibre cloth to remove any liquid or debris. 4. Reattach the accessory, making sure it's fully locked in: line up the open arrow on the accessory with the arrow on the back of the styler, then press and twist until the solid arrow lines up and it clicks into place. 5. Switch the styler on again. Avoid resting accessories on wet surfaces, as moisture on the pins can cause this error. If the lights are still blinking, please contact us. It helps to have a photo of the label showing the model and serial number, your proof of purchase, and a photo or short video of the fault ready.
What does it mean when the left and right airflow lights are blinking white and the left and right temperature lights are blinking red?
This means there could be an issue with the connection between the accessory and the styler. 1. Switch the styler off. 2. If your plug has a Reset button, press it, then switch the styler on again. 3. If the lights are still blinking, remove the accessory and turn it upside down. You'll see several shiny gold pins on the bottom. Wipe the pins with a dry microfibre cloth to remove any liquid or debris. 4. Reattach the accessory, making sure it's fully locked in: line up the open arrow on the accessory with the arrow on the back of the styler, then press and twist until the solid arrow lines up and it clicks into place. 5. Switch the styler on again. Avoid resting accessories on wet surfaces, as moisture on the pins can cause this error. If the lights are still blinking, please contact us. It helps to have a photo of the label showing the model and serial number, your proof of purchase, and a photo or short video of the fault ready.
What does it mean when the middle airflow light is blinking white and the left temperature light is blinking red?
This means the styler isn't reaching the set temperature. 1. Switch it off, leave it off for a minute, then switch it on again. 2. If the lights are still blinking, plug the styler into a different power point in another room. This is a high-powered styler and should only be used with a power point that supplies the right voltage. It shouldn't be used with a voltage converter, a power board or an extension lead. If the lights are still blinking, please contact us. It helps to have a photo of the label showing the model and serial number, your proof of purchase, and a photo or short video of the fault ready.
What does it mean when the left airflow light is blinking white and the right temperature light is blinking red?
This means there may be an issue with your power point. Try plugging the styler into a different power point in another room. If the lights are still blinking, please contact us. It helps to have a photo of the label showing the model and serial number, your proof of purchase, and a photo or short video of the fault ready.
Accessories
Why do my Shark Glam accessories keep falling off?
First, check the nozzle and the accessory for any cracks, bends or other damage. If either was damaged when it arrived, please contact us. Replacement accessories are available to purchase if one has been damaged since. If there's no visible damage: 1. Line up the open arrow on the back of the accessory with the arrow on the back of the styler. 2. Press the accessory into the nozzle and twist it until the solid arrow on the accessory lines up with the arrow on the styler. It's properly attached when it clicks into place. 3. Check the accessory lock button is positioned at the top of its slot. 4. Switch the styler on and check the accessory stays attached. If it still comes off, try attaching a different accessory to see whether it stays on. If your accessories still won't stay attached, please contact us and let us know which accessories are affected.
My Shark Glam won't lock or stay locked in styling wand or hair dryer mode. What should I do?
First, look closely at the hinge lock and the rotation point. If there's visible damage and it arrived that way, please contact us. If everything looks fine: 1. To change from styling wand mode to hair dryer mode, slide down the lock and rotate the nozzle left until it clicks into place. 2. To change back to styling wand mode, slide down the lock and rotate the nozzle right. 3. Check the hinge lock button is positioned at the top of its slot. 4. Try rotating the nozzle without touching the hinge lock button. It should stay locked. If the nozzle rotates without you holding the lock down, please contact us. It helps to have a photo of the label showing the model and serial number, your proof of purchase, and a photo or short video of the fault ready.
A button on my Shark Glam has come off. What should I do?
If the styler arrived this way, or a button has come off since, please contact us. It helps to have a photo of the label showing the model and serial number, your proof of purchase, and a photo of the affected button ready.
Why is my hair snagging on a Shark Glam attachment?
These tips usually help: 1. Section your hair before you start styling. 2. Try different section sizes, as the best size can vary with your hair type. 3. Position your hair in the middle of the straightener or brush for the best results. If your hair still snags after trying these tips, please contact us and let us know which attachment you're using.
Controls
Why aren't the airflow and temperature buttons on my Shark Glam working?
The lights and settings only change while the styler is switched on. 1. Slide the power button up to turn it on. 2. Press the airflow and temperature buttons. They should slide inward slightly as you press them. 3. Check that the lights change each time you press a button. If the styler won't turn on, see the question on this page about the Shark Glam not turning on. If the buttons don't move inward when pressed, or they move but the lights don't change, please contact us. It helps to have a photo of the label showing the model and serial number, your proof of purchase, and a photo or short video of the fault ready.
Why isn't the Cool Shot button working on my Shark Glam?
Cool Shot only works while the styler is switched on and while you're holding the button down. 1. Slide the power button up to wet mode to turn the styler on. 2. Press and hold the Cool Shot button. It should press in slightly. 3. While you hold it, all the temperature lights turn off, the airflow lights stay on, and the Fusion LED lights up dark blue. If the styler won't turn on, see the question on this page about the Shark Glam not turning on. If you hold the button and the temperature lights don't turn off, or the button doesn't press in, please contact us. It helps to have a photo of the label showing the model and serial number, your proof of purchase, and a photo or short video of the fault ready.
Dry mode isn't working, or the light isn't changing in Dry mode. What should I do?
When you first switch to Dry mode, the light flashes yellow while the ceramic plates heat up. This takes around 45 seconds. Once they're heated, the light turns solid green and the airflow switches on automatically. The first time you use Dry mode, it starts on medium airflow and medium temperature. After that, your Shark Glam remembers your last settings, so if the airflow doesn't come on, it may have been turned off the last time you used it. 1. Switch to Dry mode and check the light is flashing yellow. 2. Wait 45 seconds for it to turn green. 3. If the light isn't flashing yellow and you're using an extension lead, unplug it and plug the styler straight into a wall power point, as it shouldn't be used with an extension lead. If the styler won't turn on, see the question on this page about the Shark Glam not turning on. If the light flashes yellow but doesn't turn green after 45 seconds, please contact us. It helps to have a photo of the label showing the model and serial number, your proof of purchase, and a photo or short video of the fault ready.
Why doesn't the sound change when I close the straightener arms?
The change in sound is harder to hear on low and medium airflow, so switch to high airflow first. If you're already on high airflow, your hair sections may be too large. Try using smaller sections when straightening. If you still don't hear a difference with high airflow and smaller sections, please contact us.
Noise
Why is my Shark Glam making a loud or unusual noise?
A loud or unusual noise can mean the filter is clogged. Switch the styler off, unplug it and let it cool, then clean the filter: 1. Switch the styler off and unplug it. 2. Slide the filter cover off the bottom of the unit. 3. Gently brush away any built-up dust from the filter screen using a new toothbrush, or wipe it with a dry microfibre cloth. 4. Slide the filter cover back onto the bottom of the unit until it clicks into place, then switch the styler back on. Cleaning the filter once a month helps keep your Shark Glam performing well and helps prevent overheating. If the noise is still there after cleaning, please contact us. It helps to have a photo of the label showing the model and serial number, your proof of purchase, and a photo or short video of the fault ready. Let us know what the noise sounds like and when it happens.





